Warrenberg wireless glue production line

Germany's Wohlberg Binder, a post-press finishing machine represented by Germany's Mann Rolland and Daqin Xinxing, has recently successfully installed and commissioned five production lines at Shandong Xinhua Printing Factory. These five production lines are respectively equipped with Its five branches are Jinan Plant, Weifang Plant, Dezhou Plant, Taian Plant and Linyi Plant. Another Warrenberg production line will also be installed at the printing plant in Shaanxi Province in early August 1999. From then on, Warrenberg's new champion 8000 type perfect binding machine will set a good example for mainland China's book printing and binding manufacturers.
The champion 8000 type wireless glue binding line consists of 5 parts:
1、Sprinter SPRINTER 7011 pager;
2. Champion CHAMPION 8000 Binder;
3, TS12 broken the machine;
4. TRIM TEC cuts the book on three sides.
SPRINTER 7011 type collation machine adopts modular design principle. According to user requirements, it can be equipped with a maximum of 32 book desks. The collation machine can be used alone or can be used online with the Binder. The electronic operating device equipped with the collating machine includes a LED display capable of providing information on page faults or double faults in simple words, both ACC and PTI-CONTROL control systems; the internal clutch can rotate the roller of the transfer device. The tape has a 51 percent reduction called "half-speed function". This technology allows the use of a double-speed transmission chain to take up half of the separation speed so that twice as many stickers can be loaded into the cassette. , For thinner paper materials and less number of books, the use of half-speed matching can increase the speed and efficiency of the entire production line; the tilt-type paper table facilitates the operation of the paper, so that the operator only needs to be in the collating machine. The side carries out the paper and adjusts the operation; Through the PLC programmable controller carries on the electronic control to the entire machine, every four work is equipped with the separate computer control system.
Champion CHAMPION 8000 Binder is the host for the entire production line. The entire line has a production speed of 8000 hrs/hr and can produce single-link and double-link products. According to the needs of users, this equipment is equipped with cold gel, hot-melt adhesives and PUR devices and high-frequency drying facilities. The machine adopts a novel design that can meet the various requirements of glue-binding technology and achieve excellent quality standards for bookbinding. Its book preparation work can be equipped with up to 5 stations, each equipped with an electric height adjustment device. The operator can directly control the machine using a simple display operation panel, or perform control operation at the center console through the BIND-COM control software. The squeegee control device equipped with the squeegee control device can be adjusted individually to the required height and the thickness of the inner book block. The patented combined pre-glue device is provided with a minimum liquid in the tank. The surface indicator, its digital display device will show the relevant parameters of each gluing device. All Gluing Systems of Warrenberg, such as the hot melt adhesive and the glue tank of the cold melt adhesive system, can be used interchangeably. The second upper adhesive station can also be switched to the upper gauze station. Its optional equipment BIND-COM diagnostic software enables machine operators to quickly and selectively respond to various faults in the machine, such as machine speed, glue temperature or the number of adhesive signatures, etc., and are permanently stored by the combination software. Go to the computer and display it on a color display. If some part of the machine fails, the fault information analyzed by the software after the diagnosis is also displayed.
The intelligent conveyor belt device controls the speed of each part of the conveyor belt independently from the center console, so that the machine can be broken and the three-faced knife can match the host speed. Its compact layout greatly saves the floor space of the factory, can be debugged to overlap the book, and the transmission allows the cooling time to be extended. Warreng does not emphasize increasing the length of the conveyor belt.
The Warrenberg company has successfully installed the two hundred Xintai TS12 type breaking machine in Germany and Europe. This machine is mainly designed for the production of double joints. In Europe, a slitting method such as a middle saw blade is usually used. Due to the fact that the country's signatures are not the norm, the Warrenberg company has added a second saw blade to its needs to meet the needs of Chinese users.
The last part of the whole sheet is a three-faceted book cutter, which is a very critical part. The TRIM TEC 751 three-point knife, which was selected the most, provided the guarantee for the whole machine to reach 8,000 pieces/hour. Warrenberg is a world-renowned three-knife and cutter manufacturer. Its equipment uses a cast iron frame, which can improve the cutting method, greatly reducing the cutting noise and improving the cutting quality.
In the end, the Warrenberg company hopes to establish long-term contacts with the users of the vast majority of the printing industry in China and make an effort to improve the quality of bookbinding in China.